Bid Specifications

PART No. 100002 - MODEL C-10 WITH No. 4UV SAFETY

Stationary crucible and pot furnace, for melting aluminum in iron or steel pots or aluminum and brass in crucible in furnace chamber. Capacity No. 10 or No. 16 crucible or a 6" diameter x 8" deep metal pot suspended in furnace cover ring. Furnace lining, lid and cover ring are high alumina air rammed sections, backed with refractory insulation. Chamber size 10" diameter x 11" deep; with tangent fired burner and side exhaust port; drop type lid and refractory lid ring. Temperature range to 2400° F, nominal 235,000 BTU; for natural or bottled gas; with high speed universal brush type motor blower rated at 1/3 HP, 120 volt, single phase, (60 hz. only). Complete with silicon carbide rest block and 4 UV ultra violet combustion safeguard system. Approximate shipping weight 315 pounds.

PART No. 0900001 - MODEL C-9 WITH No. 4UV SAFETY

Specifications same as C-10 per above except without pot ring - for crucible melting only. Approximate shipping weight 290 pounds.

PART No. 900005 - MODEL C-20 WITH No. 4UV SAFETY

Stationary crucible and pot furnace for melting aluminum in iron or steel pots or aluminum and brass in crucible in furnace chamber. Capacity No. 30 crucible for brass, No. 40 crucible for melting and ladling aluminum or a 8" diameter x 10" deep cast iron pot suspended in furnace cover ring. Furnace lining, cover ring and drop lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size: 14" diameter x 16" deep. Rated for 2400° F, nominal 325,000 BTU for natural or bottled gas; complete with a No. 175 Turbo Blower with standard 1/2 HP, ball bearing, 3600 RPM, open drip-proof motor, 120/240 volt, single phase or 240/480 volt, three phase motor. Furnace supplied with silicon carbide crucible rest block and 4 UV ultra violet combustion safeguard system. Approx. shipping weight 740 pounds. (Specify voltage and phase when ordering).

PART No. 900410 - MODEL B-160 WITH No. 4UV SAFETY

Stationary crucible furnace capable of melting grey iron within one hour period; average melting speeds - aluminum, 12 to 14 minutes; yellow brass, 22 to 24 minutes; class 30 grey iron, 55 minutes. Capacity No. 16 crucible. Furnace lining and lid are high alumina air rammed sections backed with refractory insulation. Chamber size 10" diameter x 12" deep; with tangent fired burner and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F; nominal 425,000 BTU, with two valve mixer to use either natural or bottled gas. Complete with No. 175 Turbo Blower, 90 CFM, 8 oz. with 1/2 HP, 3600 RPM, ball bearing, open drip-proof, 56 frame "C" flange motor. Available in 120/240 volt, single phase, or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion safeguard system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight 550 pounds. (Specify voltage and phase when ordering).

PART No. 900015 - MODEL B-301 WITH No. 4UV SAFETY

Stationary crucible furnace, capacity No. 30 crucible, for melting aluminum and copper alloys, plus class 25 to 30 grey iron in limited quantities. Furnace lining and lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size 13" diameter x 15" deep, with dual tangent burners and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F, nominal 750,000 BTU with two valve mixer to use either natural or bottled gas. Complete with No. 1610 Industrial Turbo Blower, 150 CFM, 12 oz. with 1HP, 3600 RPM, ball bearing, drip-proof motor. Available in 120/240 volt, single phase or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion safeguard system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight 915 pounds. (Specify voltage and phase when ordering).

PART No. 900035 - MODEL B-702 WITH No. 4UV SAFETY

Stationary crucible furnace, capacity No. 40 through No. 70 crucible; for melting aluminum and copper alloys, plus Class 25 to 30 grey iron in limited quantities. Furnace lining and lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size 17" diameter x 20" deep, with dual tangent burners and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F; nominal 900,000 BTU, with two valve mixer to use either natural or bottled gas. Complete with No. 1912 Industrial Turbo Blower, 210 CFM, 12 oz. with 2 HP; 3600 RPM, ball bearing, drip-proof motor, 120/240 volt, single phase or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion safeguard system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Wiring conform to National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight 1,575 pounds. (Specify voltage and phase when ordering).

PART No. 900055 - MODEL B-1501 WITH No. 4UV SAFETY

Stationary crucible furnace, capacity No. 100 through No. 150 crucible. For melting aluminum and copper alloys, plus Class 25 to 30 grey iron in limited quantities. Furnace lining and lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size is 22" diameter x 24" deep, with four tangent burners and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F; nominal 1,200,000 BTU with two valve mixer to use either natural or bottled gas. Complete with No. 1912 Industrial Turbo Blower 230 CFM, 16 oz. with 2 HP; 3600 RPM, ball bearing, drip-proof motor, 120/240 volt, single phase, or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight 2,666 pounds. (Specify voltage and phase when ordering).

PART No. 900988 - MODEL T-160 WITH No. 4UV SAFETY

High Temperature crucible melting furnace with manual control tilt mechanism. Tilt mechanism to be oil filled gear box with worm/worm gear manual hand wheel. Designed to use No. 16 standard crucible. Tilting mechanism to give infinite control of metal stream when discharging into pouring ladle. Burner system to be equipped with turbo blower and standard induction motor in all standard voltages and phases. Wiring and electric conform to the National Electric Code. Electrical components are UL and CSA listed and approved. Shipped complete with crucible rest, combustion safeguard system, with blower air switch and magnetic line starter. Provides furnace shutdown and gas line valve closure in event of air blower failure, flame or electric power failure. Approximate shipping weight 785 pounds.

PART No. 900073 - MODEL T-301 MANUAL TILT WITH No. 4UV SAFETY

High Temperature crucible melting furnace with manual control tilt mechanism, plus automatic spark ignition and the No. 4UV ultra violet combustion safeguard system, with blower air switch and magnetic line starter. Provides furnace shutdown and gas line valve closure in event of air blower failure, flame or electric power failure. Designed to use No. 30 crucible. Tilting mechanism to give infinite control of metal stream when discharging into pouring ladle. Wiring conforms to the National Electric Code. Components UL and CSA listed and approved. Includes one No. 12 (twelve pound capacity) ladle. Shipped complete with No. 30 standard crucible and crucible rest. Approximate shipping weight 1,085 pounds.

PART No. 900060 - MODEL T-80 MANUAL TILT WITH No. 4UV SAFETY

Center Pivot Tilting Crucible Furnace, with Pivot Trunnion Bearings at its center of gravity for easy tilting with gear reducer and hand wheel. Includes the No. 4 UV ultra violet safety system consisting of automatic spark ignition, with blower air switch and continuous flame monitoring. Provides furnace shutdown in the event of electric power failure, air blower failure, or flame outage. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. For crucible sizes No. 80 through No.100. Attainable combustion chamber 2400° F, for melting aluminum and copper alloys. With cover derrick, exhaust and charging hole in cover. Furnace lining and cover are high alumina, air rammed sections, backed with high temperature insulation. Chamber size 17" diameter x 20" deep, with one tangent fired burner, nominal 850,000 BTU. Furnace equipped with manual two valve mixer to use with either manufactured or natural fuel gas. With No. 1611 Turbo Blower, 180 CFM at 12 oz. with 2 HP, 3600 RPM, ODP, ball bearing motor, 120/240 volt, single or 240/480 volt, poly phase motor with magnetic starter. Complete with silicon carbide crucible rest block 11" diameter x 2" high. Floor space required, 7' x 5', lowered height to trunnion 3', maximum overall height tilted 6'. Approximate shipping weight 1,890 pounds. (Specify voltage and phase when ordering).

PART No. 900070 - MODEL T-80 MOTORIZED TILT WITH No. 4UV SAFETY

Tilting crucible furnace, same as specified in part number 900060 (above), with combustion safeguard system, plus motorized tilt. The motorized tilt employs a reversing switch, magnetic contactor and start-stop station. Available in three phase. Approximate shipping weight 1,915 pounds.

PART No. 900075 - MODEL T-200-MT (Manual Tilt) WITH No. 4UV SAFETY

Tilting Crucible Furnace, with nose pour configuration with Pouring Spout Coaxial with trunnions. Includes the No. 4UV ultra violet safety system, consisting of automatic spark ignition, with blower air switch and continuous flame monitoring. Provides furnace shutdown in the event of electric power failure, air blower, or flame outage. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. For crucible sizes 200-275. Attainable combustion chamber temperature to 2400° F, for melting aluminum and copper alloys. With cover derrick and charging hole in cover. Furnace lining and cover are high alumina, air rammed sections, backed with high temperature insulation. Chamber size 23" diameter x 25" deep, with four tangent fired burners, nominal 1,200,000 BTU. Furnace equipped with manual two valve mixer to use either manufactured or natural fuel gas; with No. 1912 Turbo Blower, 230 CFM at 16 oz. with 2 HP, 3600 RPM, ODP, ball bearing motor, 120/240 volt, single or 240/480 volt, poly phase, 60 hz. with magnetic starter, complete with silicon carbide crucible rest block. Manual tilt requires separate overhead hoist (either hand, electric or air driven) to tilt furnace. Hoist not furnished with furnace. Floor space required, 9' x 6'; lowered height to trunnion 40", maximum overall height tilted 8'. Approximate shipping weight 3,635 pounds. (Specify voltage and phase when ordering).

PART NO. 900085 MODEL T-200-HT (Hydraulic Tilt)

Tilting Crucible Furnace, same as specified in part number 900075, with combustion safeguard system, plus hydraulic tilt. The hydraulic tilt employs two cylinders actuated by a motorized hydraulic pump with self contained reservoir, strainers, safety valves, and three position hydraulic hand valve. With magnetic contactor and start-stop station. Hydraulic system same voltage and phase as blower system. Approximate shipping weight 3,980 pounds.

PART NO. 901000 MODEL T-600-HT (Hydraulic Tilt)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch, hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for an attached lip crucible with a capacity of approximately 600 lbs. of aluminum or 1800 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures of up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 4 million BTU/HR. with an automatic proportioning system that will handle either propane or natural gas. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 11,000 lbs.

PART NO. 901010 MODEL T-600-HT-AC (Hydraulic Tilt and Automatic Control)

Tilting Crucible Furnace, nose pour configuration, same as above model except this unit has automatic temperature control. The control instrument monitors both the bath and chamber temperatures and adjusts the firing of the burner accordingly to compensate for temperature overshoot. Also featured is ramp/soak programming capability. The controls are housed in a free standing Nema 1 rated cabinet. Lid lift and furnace tilt are hydraulically assisted and have flow controls to regulate the speed of the tilt or lift. Operator platform is included so that operator can safely control metal stream when tilting. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 13,000 lbs.

PART NO. 900995 MODEL T-1000-HT (Hydraulic Tilt)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch. hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the Notional Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for a #800, #900, or #1,000 attached lip crucible with a capacity of approximately 800 to 1,000 lbs. of aluminum or 2,400 to 3,000 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures of up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 5 million BTU/HR. with an automatic proportioning system that will handle either propane or natural gas. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 13,000 lbs.

PART NO. 900999 MODEL T-1000-HT-AC (Hydraulic Tilt and Automatic Control)

Tilting Crucible Furnace. nose pour configuration, same as above model except this unit has automatic temperature control. The control instrument monitors both the bath and chamber temperatures and adjusts the firing of the burner accordingly to compensate for temperature overshoot. Also featured is ramp/soak programming capability. The controls are housed in a free standing Nema 1 rated cabinet. Lid lift and furnace tilt are hydraulically assisted and have flow controls to regulate the speed of the tilt or lift. Operator platform is included so that operator can safely control metal stream when tilting. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 14,500 lbs.

PART NO. 903000 MODEL T-1500-HT (Hydraulic Tilt)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch. hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for a #1,500 attached lip crucible with a capacity of approximately 1,500 lbs. of aluminum or 4,000 to 4,500 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures of up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 5 million BTU/HR. with an automatic proportioning system that will handle either propane or natural gas. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 15,500 lbs.

PART NO. 903005 MODEL T-1500-HT-AC (Hydraulic Tilt and Automatic Control)

PART NO. 903010 MODEL T-2000-HT (Hydraulic Tilt)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch. hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for a #2,000 attached lip crucible with a capacity of approximately 2,000 lbs. of aluminum or 5,000 to 5,500 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures of up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 5 to 6 million BTU/HR. with an automatic proportioning system that will handle either propane or natural gas. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 15,500 lbs.

PART NO. 903015 MODEL T-2000-HT-AC (Hydraulic Tilt and Automatic Control)

PART NO. 900995 MODEL T-2500-HT (Hydraulic Tilt)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition. bypass pilot, blower air switch, hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit it designed for an attached lip crucible with capacity of approximately 2,500 lbs. of aluminum or 7,500 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures of up to 2400° F are attainable. The burner system is a single, high velocity burner rated between 8-10 million BTU/HR. with an automatic proportioning system that will handle either propane or natural gas. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 16,500 lbs.

PART NO. 900999 MODEL T-2500-HT-AC (Hydraulic Tilt and Automatic Control)

MODEL DO-300A, DO-600A, DO-1000A, DO-1500A, DO-2000A

There are 5 sizes of Dip-Out furnaces. The A series are for melting aluminum or other low temperature metals. Size ranges are from 300 lbs. capacity to 2,000 lb. of aluminum. The standard model uses two thermocouples. One thermocouple is placed in the molten metal bath and the other thermocouple is placed in the firing chamber wall. Burner control is automatic by means of a two loop, microprocessor based temperature controller, using a function called Cascade Control. The control system is supplied in a free standing, Nema 1 rated cabinet with a fused disconnect. This type of control uses two setpoints and is much more accurate than the single loop type of control. It minimizes overshoot of the bath set point and also has programming features that allow the operator to have idle programs. These programs can provide additional gas savings and increased production capabilities. The burner system is a single, high velocity burner with proportioned control. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch, hi-lo gas pressure switch, double gas valves, vent valve, double gas cocks, high and low fire pre-ignition purges, gas regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low gas pressure, or flame failure. System must be manually reset after any of these failures before restarting. The safety system also has a pre-ignition purge and a diagnostic module is included for analyzing flame failure, should one occur. Wiring conforms to the National Electric Code and all components are either U.L. listed or CSA approved. The furnace lining is a combination of high alumina fire brick, backed up by 3000° castable and ceramic fiber. This combination reduces weight, gives exceptional insulating properties, and helps to reduce gas consumption. Each unit comes with a crucible base block. Crucible is extra.

PART No. 902000 - MODEL B-702-OF (Oil Fired) WITH No. 4UV SAFETY

Stationary crucible furnace, capacity No. 50 crucible; for melting aluminum and copper alloys. Furnace lining and lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size 17" diameter x 20" deep, with tangent fired burner and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F; nominal 900,000 BTU, with proportioning burner system for #2 Diesel Fuel. Available in 120/240 volt, single phase or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion safeguard system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Wiring conform to National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight of 1,800 pounds. (Specify voltage and phase when ordering).

PART No. 902005 - MODEL B-1501-OF (Oil Fired) WITH No. 4UV SAFETY

Stationary crucible furnace, capacity No. 100 crucible. For melting aluminum and copper alloys. Furnace lining and lid are high alumina, air rammed sections, backed with refractory insulation. Chamber size is 22" diameter x 24" deep, with tangent fired burner and lid exhaust opening. Attainable combustion chamber temperatures to 2400° F; nominal 1,200,000 BTU with proportioning burner system for #2 Diesel Fuel. Available in 120/240 volt, single phase, or 240/480 volt, three phase with magnetic line starter. Furnished with silicon carbide crucible rest block. No. 4UV ultra violet combustion system, consisting of an automatic spark ignition with blower air switch and continuous flame monitoring. Provides furnace shutdown in event of air blower failure, flame or power failure. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. Approximate shipping weight 2,600 pounds. (Specify voltage and phase when ordering).

PART No. 902010 - MODEL T-80-OF (Oil Fired) MANUAL TILT WITH No. 4UV SAFETY

Center Pivot Tilting Crucible Furnace, with Pivot Trunnion Bearings at its center of gravity for easy tilting with gear reducer and hand wheel. Includes the No. 4UV ultra violet safety system consisting of automatic spark ignition, with blower air switch and continuous flame monitoring. Provides furnace shutdown in the event of electric power failure, air blower failure, or flame outage. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. For crucible size No. 80. Attainable combustion chamber temps to 2400° F, for melting aluminum and copper alloys. With cover derrick, exhaust and charging hole in cover. Furnace lining and cover are high alumina, air rammed sections, backed with high temperature insulation. Chamber size 17" diameter x 20" deep, with one tangent fired burner, nominal BTU rating of 900,000/Hr., with proportioning burner system for #2 Diesel Fuel. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Available in 120/240 volt, single or 240/480 volt, poly phase motor with magnetic starter. Complete with silicon carbide crucible rest block 11" diameter x 2" high. Floor space required, 7' x 5', lowered height to trunnion 3', maximum overall height tilted 6'. Approximate shipping weight 2,600 pounds. (Specify voltage and phase when ordering).

Part No. 902011 - Motorized Tilt Option for T-80-OF

The motorized tilt option employs a reversing switch, magnetic contactors and a start/stop station in addition to a gear motor to operate the tilting action of the above furnace. Available in 3 phase only. Adds approximately 100 lbs. to the shipping weight.

PART No. 902015 - MODEL T-200-HT-OF (Hydraulic Tilt-Oil Fired) WITH No. 4UV SAFETY

Tilting Crucible Furnace, with nose pour configuration with Pouring Spout Coaxial with trunnions. Includes the No. 4UV ultra violet safety system, consisting of automatic spark ignition, with blower air switch and continuous flame monitoring. Provides furnace shutdown in the event of electric power failure, air blower, or flame outage. Wiring conforms to the National Electric Code. Electrical components are UL and CSA listed. For crucible size #200 with attached lip. Attainable combustion chamber temperatures to 2400° F, for melting aluminum and copper alloys. With cover derrick and charging hole in cover. Furnace lining and cover are high alumina, air rammed sections, backed with high temperature insulation. Chamber size 23" diameter x 25" deep, with tangent fired burner, nominal 1,200,000 BTU. Furnace equipped with proportioning burner system for #2 Diesel Fuel. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Available in 120/240 volt, single or 240/480 volt, poly phase, 60 hz. with magnetic starter. Shipped with silicon carbide crucible rest block. The hydraulic tilt employs two rams actuated by a motorized hydraulic pump with self contained reservoir, strainers, safety valves, and three position hydraulic hand valve. With magnetic contactor and start-stop station. Hydraulic system same voltage and phase as blower system. Floor space required, 9' x 6'; lowered height to trunnion 40", maximum overall height tilted 8'. Approximate shipping weight 4,200 pounds. (Specify voltage and phase when ordering).

PART NO. 902020 MODEL T-600-HT-OF (Hydraulic Tilt-Oil Fired)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch, hi-lo oil pressure switch, oil solenoid valve, shut-off cock, high and low fire pre-ignition purges, oil regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low oil pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for an attached lip crucible with a capacity of approximately 600 lbs. of aluminum or 1800 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 4 million BTU/HR. with an automatic proportioning system for #2 Diesel Fuel. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 14,000 lbs.

PART NO. 902021 MODEL T-600-HT-AC-OF (Hydraulic Tilt - Automatic Control - Oil Fired)

Tilting Crucible Furnace, nose pour configuration, same as above model except this unit has automatic temperature control. The control instrument monitors both the bath and chamber temperatures and adjusts the firing of the burner accordingly to compensate for temperature overshoot. Also featured is ramp/soak programming capability. The controls are housed in a free standing Nema 1 rated cabinet. The exhaust is to the rear. Lid lift and furnace tilt are hydraulically assisted and have flow controls to regulate the speed of the tilt or lift. Operator platform is included so that operator can safely control metal stream when tilting. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 14,500 lbs.

PART NO. 902025 MODEL T-1000-HT-OF (Hydraulic Tilt - Oil Fired)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch. hi-lo oil pressure switch, oil solenoid valve, shut-off cock, high and low fire pre-ignition purges, oil regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low oil pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for a #1,000 attached lip crucible with a capacity of approximately 1,000 lbs. of aluminum or approximately 2,800 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 5 million BTU/HR. with an automatic proportioning system. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 15,500 lbs.

PART NO. 902026 MODEL T-1000-HT-AC-OF (Hydraulic Tilt - Automatic Control - Oil Fired)

PART NO. 902030 MODEL T-2500-HT-OF (Hydraulic Tilt - Oil Fired)

Tilting Crucible Furnace, nose pour configuration, with pouring spout coaxial with trunnions. Furnace has hydraulic assisted tilt and lid lift that includes flow control valves to regulate the speed of the strokes. Operator platform is also included so that operator can safely control metal stream while tilting. Includes an FM approved safety system, which consists of spark ignition, bypass pilot, blower air switch. hi-lo oil pressure switch, oil solenoid valve, shut-off cock, high and low fire pre-ignition purges, oil regulator, and continuous flame monitoring. This system provides for automatic shut-down in the event of power failure, blower failure, too high or too low oil pressure, or flame failure. System must be manually reset after any of these failures before restarting. Wiring conforms to the National Electric Code and all components are U.L. and/or C.S.A. listed or approved. This unit is designed for a #2,500 attached lip crucible with a capacity of approximately 2,500 lbs. of aluminum or approximately 7,000 lbs. of brass and will melt all non-ferrous metals. Chamber temperatures up to 2400° F are attainable. The burner system is a single, high velocity burner rated at approximately 6 to 8 million BTU/HR. with an automatic proportioning system. Burner control is achieved manually by means of an electric switch that controls the position of the air butterfly valve. Furnace includes crucible base block. Crucible is extra. Approximate shipping weight is 23,500 lbs.

CLICK HERE : CONTINUE TO PAGE 2 OF SPECS

BENTONITE, ALLOYS & SAND

ASPHALT SHOES / PAVING

Furnace Specifications Sheet

Supplier of all Foundry needs

9Tel 978-649-0112

Fax 978-649-0114

Malcolm G. Stevens, Inc

12 Progress Ave,

Tyngsboro, MA 01879

Tel 978-649-0112

Fax 978-649-0114

E-mail: BillyS@mgstevens.com

TONGS & SHANKS

BINDERS, CORE OIL, FLUXES & DEGASSERS